2-A Y Parts List

Grease filter

Sold individually. This metallic vent hood filter collects grease particles in the air from cooking.

Long oven sensor (use wpl 12001656)

The oven sensor detects the temperature within the oven cavity and sends the information to the control board. If your oven is not heating evenly, has little or no heat when baking, or is too hot, you may need to replace the sensor. This long oven sensor kit comes with two harness adapters and is a genuine OEM part. Please remember to disconnect the power before starting your repair.

Drain pump and motor assembly (pump bracket asm)

This drain pump motor helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period. If your washer will not drain, is noisy, leaking, or pumps but will not spin, you may need to replace the drain pump motor. This is a genuine OEM part. Please remember to shut off the water supply and disconnect the power to the washer before starting your repair.

Microwave turntable tray (glass carousel tray)

This round glass carousel tray is sixteen inches in diameter.

Dryer heater element (heater element)

Drum slide (bearing)

This slide is sold individually. Some dryers require up to three of these slides . Be sure to check to make sure you order the necessary amount for your dryer.

Agitator bolt (stud-agit)

This kit contains one screw with rubber gasket and threaded sealant. The screw head is 7/16".

Oven handle end cap - left or right side (end cap handle)

This oven handle end cap connects to your oven door handle, and acts as the joint that connects it to the oven door. This part is made of black plastic and can be used as the left or right-side end cap. If your oven door handle is loose or disconnected, this part may fix the problem. The end cap will need to be screwed into the oven door itself, but simply snaps in to the door handle. This part is sold individually.

Infinite heat switch kit (stove top surface element control switch kit. If the surface element is not heating the element can be tested to determine if it is defective.)

The infinite switch controls the stove top surface burner. This switch will work with most of the electrical range models with coil burner elements.

Single heating element support clip (support bracket for oven broil element.)

The support clip is used to hold the broil element in place at the top of the oven cavity. If the clip is broken or damaged, you will need to replace the part. The support clip is made of metal, is a little over an inch long, and is sold individually. This is a genuine OEM part.

Dryer radiant flame sensor (sensor)

This part senses if the igniter is hot enough to ignite the flame for heat, allowing the gas valve to open. The sensor is three inches long and is used for many gas clothes dryers. If your dryer is not creating any heat, taking too long to dry or shuts off too soon, you may need to replace the flame sensor. This is a genuine OEM part and is made of both plastic and metal. Please remember to disconnect power to your dryer before starting your repair.

Standard y-frame range surface burner (premium surface burner - six inch)

This standard Y-frame 6” surface element is a genuine OEM part that supplies heat to the cooking surface on your range. It has four turns, a black center medallion, looped terminal ends and carries 15000 tts. If your element is not heating, you may need to replace it. Please be sure to disconnect the power to your range before starting your repair. The manufacturer suggests replacing the receptacle at the same time.

Element with limiter 6 inch - 1200w (elmnt-surf)

This 6 Inch 1200-watt radiant surface element with limiter is located under the main cooktop. When the element is turned on, it will heat up and provide heat to the cooking area on top of the range. If your element will not supply heat you will need to replace it. When replacing the radiant surface element please make sure the element is cool to touch before starting the repair. Disconnect the power to your range before beginning the repair. This is a genuine OEM part.

Charcoal air filters (filter)

This is a package of 2 filters. The charcoal filter is used in microwaves to remove food odors from the air. If your filter is damaged or strong odors are coming from your microwave, it is best to replace this part. The only tool needed for this repair is a Phillips screwdriver. First, remove screws at the top of microwave to access the filter. Next, remove filter and insert new filter by pushing it all the way back, so the edges hit the two tabs. The front edge of the filter should rest at the bottom of the cavity. Make sure to replace the grill after installing the new filter. Remember to unplug your microwave from the power source before the installation process. This part is metallic and measures about 12 inches wide and 6 inches deep.

Door handle - white (handle long white)

This part is on the outer door of the dryer.